Network Security Notes: Network Protocols: Configuring EIGRP Authentication Protocol

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

As my previous post about Understanding EIGRP protocol, this post I would like to share you about configuring EIGRP Authentication....

EIGRP Authentication between Router A and Router B

EIGRP authentication of packets has been supported since IOS version 11.3. EIGRP route authentication is similar to RIP version 2, but EIGRP authentication supports only the MD5 version of packet encryption.

EIGRP's authentication support may at first seem limited, but plain text authentication should be configured only when neighboring routers do not support MD5. Because EIGRP is a proprietary routing protocol developed by Cisco, it can be spoken only between two Cisco devices, so the issue of another neighboring router not supporting the MD5 cryptographic checksum of packets should never arise.

The steps for configuring authentication of EIGRP updates are similar to the steps for configuring RIP version 2 authentication:

1. Define the key chain using the command key−chain < name> in global configuration mode. This command transfers you to the key chain configuration mode.

2. Specify the key number with the key command in key chain configuration mode. You can configure multiple keys.

3. For each key, identify the key string with the key−string command.

4. Optionally, you can configure the period for which the key can be sent and received. Use the
following commands:

accept−lifetime {infinite|end−time|duration −seconds}
send−lifetime {infinite|end−time|duration seconds}


5. Exit key chain configuration mode with the exit command.

6. Under interface configuration mode, enable the authentication of EIGRP updates with this
command:

ip authentication key−chain eigrp

7. Enable MD5 authentication of EIGRP updates using the following command:

ip authentication mode eigrp md5

With the command below shows you how Router A should be configured to authenticate updates from Router B using EIGRP MD5 authentication,

Command Listing A: Router A's configuration with MD5 authentication:

key chain router−a
key 1
key−string eigrp
!
interface Loopback0
ip address 10.10.10.1 255.255.255.0
!
interface Ethernet0/0
ip address 10.10.11.1 255.255.255.0
!
interface Serial0/0
ip address 192.168.10.1 255.255.255.252
ip authentication mode eigrp 2 md5
ip authentication key−chain eigrp 2 router−a
clockrate 64000
!
router eigrp 2
network 10.0.0.0
network 192.168.10.0
no auto−summary
eigrp log−neighbor−changes

And the next below command here shows the configuration for Router B.

Command Listing B: Router B's configuration with MD5 authentication:

key chain router−b
key 1
key−string eigrp
!
interface Loopback0
ip address 10.10.12.1 255.255.255.0
!
interface Ethernet0/0
ip address 10.10.13.1 255.255.255.0
!
interface Serial0/0
ip address 192.168.10.2 255.255.255.252
ip authentication mode eigrp 2 md5
ip authentication key−chain eigrp 2 router−b
clockrate 64000
!
router eigrp 2
network 10.0.0.0
network 192.168.10.0
no auto−summary
eigrp log−neighbor−changes

The Command Listing A configures Router A with a key chain value of router−a, a key value of 1, and a key−string value of eigrp. The Command Listing B configures Router B with a key chain value of router−b, a key value of 1, and a key−string value of eigrp. Notice again that the key chain need not match between routers; however, the key number and the key string associated with the key value must match between routers configured to use that key value. Although debugging of encrypted EIGRP packets is somewhat limited, a few commands can be used to verify that packet encryption is taking place correctly. Two of those commands are debug eigrp packet and show ip route. The debug eigrp packet command informs you if the router has received a packet with the correct key value and key string. The output of issuing this command can be seen here:

Router−A#debug eigrp packet
EIGRP Packets debugging is on
(UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK)
Router−A#
EIGRP: received packet with MD5 authentication
EIGRP: received packet with MD5 authentication

Router A is receiving MD5−authenticated packets from it neighbor, Router B. However, we cannot fully determine whether or not the authentication is taking place correctly without issuing the show ip route command on Router A. This allows us to look at the route table and determine that packet authentication is taking place correctly because the routes that Router B has sent to Router A are installed into the route table. Listing 1.7 displays the output of the show ip route command.

Listing Command C: Route table of Router A with correct authentication configured:

Router−A#sh ip route
...
C 192.168.10.0/24 is directly connected, Ethernet0/0
C 10.10.10.0 is directly connected, Loopback0

C 10.10.11.0 is directly connected, Ethernet0/0
D 10.10.12.0 [90/409600] via 192.168.10.2, 00:18:36, Serial0/0
D 10.10.13.0 [90/409600] via 192.168.10.2, 00:18:36, Serial0/0
Router−A#

You can change Router A's key−string value for key 1 to see what kind of an effect this will have.
The following lines will change the key−string value for key 1 on Router A to ospf:

Router−A#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router−A(config)#key chain router−a
Router−A(config−keychain)#key 1
Router−A(config−keychain−key)#key−string ospf
Router−A(config−keychain−key)#end
Router−A#

Now that Router A has a different key string associated with key 1, you would assume that packet authentication is not taking place correctly. By issuing the debug eigrp packet command, you can see that there is indeed a problem with authentication:

Router−A#debug eigrp packet
EIGRP Packets debugging is on
(UPDATE, REQUEST, QUERY, REPLY, HELLO, IPXSAP, PROBE, ACK)
Router−A#
EIGRP: received packet with MD5 authentication
EIGRP: ignored packet from 192.168.10.2 opcode = 5 (invalid
authentication)

Taking a quick look at the route table confirms that the authentication is incorrectly configured. Now that the key strings are different, no routes from Router B are installed into the route table of Router A. Listing Command C: displays the routing table of Router A.
Listing Command C:: Route table of Router A with incorrect authentication configured.

Router−A#sh ip route
...
C 192.168.10.0/24 is directly connected, Ethernet0/0
10.0.0.0/24 is subnetted, 2 subnets
C 10.10.10.0 is directly connected, Loopback0
C 10.10.11.0 is directly connected, Loopback1
Router−A#

NOTE: You can also issue the show ip eigrp neighbor command to determine if authentication is configured correctly. If authentication is correctly configured, the neighboring router will be displayed in the output of the command. If authentication is incorrectly configured, the neighbor will not be displayed in the output.



Other sites you may want to see:

Entertainment on Flixya: http://visalittleboy.flixya.com/
WWE: http://visa-wwe.blogspot.com/
The Kingdom of Wonder: http://welcome2cambodia.blogspot.com/
Daily Blogging: http://visablogging.blogspot.com/
Love Sharing: http://visa-love.blogspot.com/
NetworkSecurity: http://networksecuritynotes.blogspot.com/
About Insurance:http://visa-insurance.blogspot.com
All about Love: http://visa-love.blogspot.com/
Learning English Online: http://visa-elb.blogspot.com/
Discovery Internet: http://visa-isp.blogspot.com/

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Network Security Notes: Network Protocols: Understanding EIGRP and IGRP Protocols

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

Network Security Notes: Network Protocols: Understanding EIGRP and IGRP Protocols

Enhanced Interior Gateway Routing Protocol - (EIGRP) is a Cisco proprietary routing protocol loosely based on their original IGRP. EIGRP is an advanced distance-vector routing protocol, with optimizations to minimize both the routing instability incurred after topology changes, as well as the use of bandwidth and processing power in the router. Routers that support EIGRP will automatically redistribute route information to IGRP neighbors by converting the 32 bit EIGRP metric to the 24 bit IGRP metric. Most of the routing optimizations are based on the Diffusing Update Algorithm (DUAL) work from SRI, which guarantees loop-free operation and provides a mechanism for fast convergence.

What is IGRP?

Interior Gateway Routing Protocol (IGRP) is a distance vector interior routing protocol (IGP) invented by Cisco. It is used by routers to exchange routing data within an autonomous system.

IGRP is a proprietary protocol. IGRP was created in part to overcome the limitations of RIP (maximum hop count of only 15, and a single routing metric) when used within large networks. IGRP supports multiple metrics for each route, including bandwidth, delay, load, MTU, and reliability; to compare two routes these metrics are combined together into a single metric, using a formula which can be adjusted through the use of pre-set constants. The maximum hop count of IGRP-routed packets is 255 (default 100), and routing updates are broadcast every 90 seconds (by default).

IGRP is considered a classful routing protocol. Because the protocol has no field for a subnet mask, the router assumes that all interface addresses within the same Class A, Class B, or Class C network have the same subnet mask as the subnet mask configured for the interfaces in question. This contrasts with classless routing protocols that can use variable length subnet masks. Classful protocols have become less popular as they are wasteful of IP address space.

What is Distance-vector routing protocol?

In computer communication theory relating to packet-switched networks, a distance-vector routing protocol is one of the two major classes of routing protocols, the other major class being the link-state protocol. A distance-vector routing protocol uses the Bellman-Ford algorithm to calculate paths.

A distance-vector routing protocol requires that a router informs its neighbors of topology changes periodically and, in some cases, when a change is detected in the topology of a network. Compared to link-state protocols, which require a router to inform all the nodes in a network of topology changes, distance-vector routing protocols have less computational complexity and message overhead.

Distance Vector means that Routers are advertised as vector of distance and direction. 'Direction' is represented by next hop address and exit interface, whereas 'Distance' uses metrics such as hop count.

Routers using distance vector protocol do not have knowledge of the entire path to a destination. Instead DV uses two methods:

1. Direction in which or interface to which a packet should be forwarded.
2. Distance from its destination.

Examples of distance-vector routing protocols include Routing Information Protocol Version 1 & 2, RIPv1 and RIPv2 and IGRP. EGP and BGP are not pure distance-vector routing protocols because a distance-vector protocol calculates routes based only on link costs whereas in BGP, for example, the local route preference value takes priority over the link cost.

A link-state routing protocol is one of the two main classes of routing protocols used in packet switching networks for computer communications, the other major class being the distance-vector routing protocol. Examples of link-state routing protocols include OSPF and IS-IS.

The link-state protocol is performed by every switching node in the network (i.e. nodes that are prepared to forward packets; in the Internet, these are called routers). The basic concept of link-state routing is that every node constructs a map of the connectivity to the network, in the form of a graph, showing which nodes are connected to which other nodes. Each node then independently calculates the next best logical path from it to every possible destination in the network. The collection of best paths will then form the node's routing table.

This contrasts with distance-vector routing protocols, which works by having each node share its routing table with its neighbors. In a link-state protocol the only information passed between nodes is connectivity related.

Link state algorithms are sometimes characterized by the ‘Each router tells the world about its neighbors’.

Understanding About Diffusing Update Algorithm (DUAL):

DUAL, the Diffusing Update ALgorithm, is the algorithm used by Cisco's EIGRP routing protocol to ensure that a given route is recalculated globally whenever it might cause a routing loop. According to Cisco, the full name of the algorithm is DUAL finite-state machine (DUAL FSM). EIGRP is responsible for the routing within an autonomous system and DUAL responds to changes in the routing topology and dynamically adjusts the routing tables of the router automatically.

EIGRP uses a feasibility condition to ensure that only loop-free routes are ever selected. The feasibility condition is conservative: when the condition is true, no loops can occur, but the condition might under some circumstances reject all routes to a destination although some are loop-free.

When no feasible route to a destination is available, the DUAL algorithm invokes a Diffusing Computation to ensure that all traces of the problematic route are eliminated from the network. At which point the normal Bellman-Ford algorithm is used to recover a new route.

!!! DUAL Operation:

DUAL uses three separate tables for the route calculation. These tables are created using information exchanged between the EIGRP routers. The information is different than that exchanged by link-state routing protocols. In EIGRP, the information exchanged includes the routes, the "metric" or cost of each route, and the information required to form a neighbor relationship (such as AS number, timers, and K values). The three tables and their functions in detail are as follows:

* Neighbor table contains information on all other directly connected routers. A separate table exists for each supported protocol (IP, IPX, etc). Each entry corresponds to a neighbour with the description of network interface and address. In addition, a timer is initialized to trigger the periodic detection of whether the connection is alive. This is achieved through "Hello" packets. If a "Hello" packet is not received from a neighbor for a specified time period, the router is assumed down and removed from the neighbor table.
* Topology table contains the metric (cost information) of all routes to any destination within the autonomous system. This information is received from neighboring routers contained in the Neighbor table. The primary (successor) and secondary (feasible successor) routes to a destination will be determined with the information in the topology table. Among other things, each entry in the topology table contains the following:

"FD (Feasible Distance)": The calculated metric of a route to a destination within the autonomous system.
"RD (Reported Distance)": The metric to a destination as advertised by a neighboring router. RD is used to calculate the FD, and to determine if the route meets the "feasibility condition".
Route Status: A route is marked either "active" or "passive". "Passive" routes are stable and can be used for data transmission. "Active" routes are being recalculated, and/or not available.

* Routing table contains the best route(s) to a destination (in terms of the lowest "metric"). These routes are the successors from the topology table.

DUAL evaluates the data received from other routers in the topology table and calculates the primary (successor) and secondary (feasible successor) routes. The primary path is usually the path with the lowest metric to reach the destination, and the redundant path is the path with the second lowest cost (if it meets the feasibility condition). There may be multiple successors and multiple feasible successors. Both successors and feasible successors are maintained in the topology table, but only the successors are added to the routing table and used to route packets.

For a route to become a feasible successor, its RD must be smaller than the FD of the successor. If this feasibility condition is met, there is no way that adding this route to the routing table could cause a loop.

If all the successor routes to a destination fail, the feasible successor becomes the successor and is immediately added to the routing table. If there is no feasible successor in the topology table, a query process is initiated to look for a new route.

Do you know SRI?

SRI International, founded as Stanford Research Institute, is one of the world's largest contract research institutes. Based in the United States, the trustees of Stanford University established it in 1946 as a center of innovation to support economic development in the region. It was later incorporated as an independent non-profit organization under U.S. and California laws. SRI's headquarters are in Menlo Park, California, near the Stanford University campus. Curtis Carlson, Ph.D., is SRI's president and CEO. Year 2009 revenue for SRI, including its subsidiary, Sarnoff Corporation, was approximately $470 million. As of 2010, SRI and Sarnoff employ about 1,700 staff members combined.

SRI's mission is discovery and the application of science and technology for knowledge, commerce, prosperity, and peace. It performs client-sponsored research and development for government agencies, commercial businesses, and private foundations. It also licenses its technologies, forms strategic partnerships, and creates spin-off companies. SRI's focus areas include communications and networks, computing, economic development and science and technology policy, education, energy and the environment, engineering systems, pharmaceuticals and health sciences, homeland security and national defense, materials and structures, and robotics. SRI has been awarded more than 1,000 patents and patent applications worldwide.

Understanding About Convergence (routing protocol):


Convergence is an important notion for a set of routers that engage in dynamic routing. For a set of routers to have converged, they must have collected all available topology information from each other via the implemented routing protocol, the information they gathered must not contradict any other router's topology information in the set, and it must reflect the real state of the network. In other words: In a converged network all routers "agree" on what the network topology looks like.

All Interior Gateway Protocols rely on convergence to function properly; it is the normal state of an operational autonomous system. The Exterior Gateway Routing Protocol BGP typically never converges because the Internet is too big for changes to be communicated fast enough.

Convergence process:

When a routing protocol process is enabled, a router will attempt to exchange information about the topology of the network. The extent of this information exchange, the way it is sent and received, and the type of information required vary widely depending on the routing protocol in use, see e.g. RIP, OSPF, BGP4.

A state of convergence is achieved once all routing protocol-specific information has been distributed to all routers participating in the routing protocol process. Any change in the network that affects routing tables will break the convergence temporarily until this change has been successfully communicated to all other routers.

Basic operation of EIGRP:

The data EIGRP collects is stored in three tables:

* Neighbor Table: Stores data about the neighboring routers, i.e. those directly accessible through directly connected interfaces.

* Topology Table: Confusingly named, this table does not store an overview of the complete network topology; rather, it effectively contains only the aggregation of the routing tables gathered from all directly connected neighbors. This table contains a list of destination networks in the EIGRP-routed network together with their respective metrics. Also for every destination, a successor and a feasible successor are identified and stored in the table if they exist. Every destination in the topology table can be marked either as "Passive", which is the state when the routing has stabilized and the router knows the route to the destination, or "Active" when the topology has changed and the router is in the process of (actively) updating its route to that destination.

* Routing table: Stores the actual routes to all destinations; the routing table is populated from the topology table with every destination network that has its successor and optionally feasible successor identified (if unequal-cost load-balancing is enabled using the variance command). The successors and feasible successors serve as the next hop routers for these destinations.

Unlike most other distance vector protocols, EIGRP does not rely on periodic route dumps in order to maintain its topology table. Routing information is exchanged only upon the establishment of new neighbor adjacencies, after which only changes are sent. Also, it uses route tagging.

Another useful link about EIGRP and IGRP:

Introduction to EIGRP (CISCO)



Other sites you may want to see:

Entertainment on Flixya: http://visalittleboy.flixya.com/
WWE: http://visa-wwe.blogspot.com/
The Kingdom of Wonder: http://welcome2cambodia.blogspot.com/
Daily Blogging: http://visablogging.blogspot.com/
Love Sharing: http://visa-love.blogspot.com/
NetworkSecurity: http://networksecuritynotes.blogspot.com/
About Insurance:http://visa-insurance.blogspot.com
All about Love: http://visa-love.blogspot.com/
Learning English Online: http://visa-elb.blogspot.com/
Discovery Internet: http://visa-isp.blogspot.com/

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Network Technology: Network Security: How to Configuring RIP Authentication

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

As my previous post about RIP Protocol, here this post I want to show you how to configure RIP Authentication...

Generally, There are two versions of Routing Information Protocol (RIP): version 1 and version 2. RIP version 1 does not support authentication of routing updates; however, RIP version 2 supports both plain text and MD5 authentication.

The Picture Figure below shows two routers, Router A and Router B, that exchange
RIP version 2 MD5 authentication updates.

Router A and Router B configured for RIP authentication

Configuring authentication of RIP version 2 updates is fairly easy and very uniform. The basic configuration includes the following steps:

1. Define the key chain using the command key−chain <> in global configuration mode. This command transfers you to the key chain configuration mode.

2. Specify the key number with the key <> command in key chain configuration mode.You can configure multiple keys.

3. For each key, identify the key string with the key−string <> command.

4. Configure the period for which the key can be sent and received. Use the following
commands:

accept−lifetime {infinite|end−time|duration −
seconds}
send−lifetime {infinite|end−time|duration seconds}

5. Exit key chain configuration mode with the exit command.

6. Under interface configuration mode, enable the authentication of RIP updates with this command:

ip rip authentication key−chain

This command is all that is needed to use plain text authentication.

7. Optionally, under interface configuration mode, enable MD5 authentication of RIP updates using the ip rip authentication mode md5 command.

The listings that follow show how Router A and Router B in Figure 1.3 should be configured to authenticate updates from one another using RIP MD5 authentication. Listing 1.1 shows the configuration of Router A, and Listing 1.2 shows the configuration of Router B.

Listing 1.1: Router A's configuration with MD5 authentication:

key chain systems
key 1
key−string router
!
interface Loopback0
ip address 10.10.10.1 255.255.255.0
!
interface Ethernet0/0
ip address 10.10.11.1 255.255.255.0
!
interface Serial0/0
ip address 192.168.10.1 255.255.255.252
ip rip authentication mode md5
ip rip authentication key−chain systems
clockrate 64000
!
router rip
version 2
network 10.0.0.0
network 192.168.10.0
no auto−summary

Listing 1.2: Router B's configuration with MD5 authentication:

key chain cisco
key 1
key−string router
!
interface Loopback0
ip address 10.10.12.1 255.255.255.0
!
interface FastEthernet0/0
ip address 10.10.13.1 255.255.255.0
!
interface Serial0/0
ip address 192.168.10.2 255.255.255.252
ip rip authentication mode md5
ip rip authentication key−chain cisco
!
router rip
version 2
network 10.0.0.0
network 192.168.10.0
no auto−summary

The configuration in Listing 1.1 displays Router A's MD5 configuration. Router A is configured with a key chain value of systems, a key value of 1, and a key−string value of router. Listing 1.2 displays Router B's MD5 configuration. Router B is configured with a key chain value of cisco, a key value of 1, and a key−string value of router.

Note Notice that the key−chain command of each router can have a different value; however, the key−string command must match for each key that is configured on each neighbor.

You can use the command debug ip rip to examine how RIP receives the encrypted routing updates. Entering this command on Router A and Router B displays the output shown in Listing 1.3 and Listing 1.4, respectively.


Listing 1.3: The output of the command debug ip rip displays how Router A receives RIP routing
updates from Router B:

Router−A#debug ip rip
RIP protocol debugging is on
Router−A#
RIP: received packet with MD5 authentication
RIP: received v2 update from 192.168.10.2 on Serial0/0
10.10.12.0/24 −> 0.0.0.0 in 1 hops
10.10.13.0/24 −> 0.0.0.0 in 1 hops

Listing 1.4: The output of the command debug ip rip displays how Router B receives RIP routing
updates from Router A:

Router−B#debug ip rip
RIP protocol debugging is on
Router−B#
RIP: received packet with MD5 authentication
RIP: received v2 update from 192.168.10.1 on Serial0/0
10.10.10.0/24 via 0.0.0.0 in 1 hops
10.10.11.0/24 via 0.0.0.0 in 1 hops



Other sites you may want to see:

Entertainment on Flixya: http://visalittleboy.flixya.com/
WWE: http://visa-wwe.blogspot.com/
The Kingdom of Wonder: http://welcome2cambodia.blogspot.com/
Daily Blogging: http://visablogging.blogspot.com/
Love Sharing: http://visa-love.blogspot.com/
NetworkSecurity: http://networksecuritynotes.blogspot.com/
About Insurance:http://visa-insurance.blogspot.com
All about Love: http://visa-love.blogspot.com/
Learning English Online: http://visa-elb.blogspot.com/
Discovery Internet: http://visa-isp.blogspot.com/

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Network Technology: Network Security: Learning About RIP (Routing Information Protocol)

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

The Routing Information Protocol (RIP) is a dynamic routing protocol used in local and wide area networks. As such it is classified as an interior gateway protocol (IGP). It uses the distance-vector routing algorithm. It was first defined in RFC 1058 (1988). The protocol has since been extended several times, resulting in RIP Version 2 (RFC 2453). Both versions are still in use today, however, they are considered to have been made technically obsolete by more advanced techniques such as Open Shortest Path First (OSPF) and the OSI protocol IS-IS. RIP has also been adapted for use in IPv6 networks, a standard known as RIPng (RIP next generation), published in RFC 2080 (1997).

The routing algorithm used in RIP, the Bellman-Ford algorithm, was first deployed in a computer network in 1967, as the initial routing algorithm of the ARPANET.

The earliest version of the specific protocol that became RIP was the Gateway Information Protocol, part of the PARC Universal Packet internetworking protocol suite, developed at Xerox Parc. A later version, named the Routing Information Protocol, was part of Xerox Network Systems.

A version of RIP which supported the Internet Protocol (IP) was later included in the Berkeley Software Distribution (BSD) of the Unix operating system. It was known as the routed daemon. Various other vendors would create their own implementations of the routing protocol. Eventually, RFC 1058 unified the various implementations under a single standard.

RIP is a distance-vector routing protocol, which employs the hop count as a routing metric. The hold down time is 180 seconds. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for RIP is 15. This hop limit, however, also limits the size of networks that RIP can support. A hop count of 16 is considered an infinite distance and used to deprecate inaccessible, inoperable, or otherwise undesirable routes in the selection process.

RIP implements the split horizon, route poisoning and holddown mechanisms to prevent incorrect routing information from being propagated. These are some of the stability features of RIP. It is also possible to use the so called RIP-MTI (Minimal Topology Information) algorithm to cope with the count to infinity problem. With its help, it is possible to detect every possible loop with a very small computation effort.

Originally each RIP router transmitted full updates every 30 seconds. In the early deployments, routing tables were small enough that the traffic was not significant. As networks grew in size, however, it became evident there could be a massive traffic burst every 30 seconds, even if the routers had been initialized at random times. It was thought, as a result of random initialization, the routing updates would spread out in time, but this was not true in practice. Sally Floyd and Van Jacobson showed in 1994 that, without slight randomization of the update timer, the timers synchronized over time. In most current networking environments, RIP is not the preferred choice for routing as its time to converge and scalability are poor compared to EIGRP, OSPF, or IS-IS (the latter two being link-state routing protocols), and (without RIP-MTI) a hop limit severely limits the size of network it can be used in. However, it is easy to configure, because RIP does not require any parameters on a router unlike other protocols.

RIP is implemented on top of the User Datagram Protocol as its transport protocol. It is assigned the reserved port number 520.

RIP Versions:

There are three versions of the Routing Information Protocol: RIPv1, RIPv2, and RIPng.

RIP version 1

The original specification of RIP, defined in RFC 1058, uses classful routing. The periodic routing updates do not carry subnet information, lacking support for variable length subnet masks (VLSM). This limitation makes it impossible to have different-sized subnets inside of the same network class. In other words, all subnets in a network class must have the same size. There is also no support for router authentication, making RIP vulnerable to various attacks.The RIP version 1 works when there is only 16 hop counts(0-15).If there are more than 16 hops between two routers it fails to send data packets to the destination address.

RIP version 2

Due to the deficiencies of the original RIP specification, RIP version 2 (RIPv2) was developed in 1993 and last standardized in 1998. It included the ability to carry subnet information, thus supporting Classless Inter-Domain Routing (CIDR). To maintain backward compatibility, the hop count limit of 15 remained. RIPv2 has facilities to fully interoperate with the earlier specification if all Must Be Zero protocol fields in the RIPv1 messages are properly specified. In addition, a compatibility switch feature allows fine-grained interoperability adjustments.

In an effort to avoid unnecessary load on hosts that do not participate in routing, RIPv2 multicasts the entire routing table to all adjacent routers at the address 224.0.0.9, as opposed to RIPv1 which uses broadcast. Unicast addressing is still allowed for special applications.

(MD5) authentication for RIP was introduced in 1997.

RIPv2 is Internet Standard STD-56.

Route tags were also added in RIP version 2. This functionality allows for routes to be distinguished from internal routes to external redistributed routes from EGP protocols.

RIPng

RIPng (RIP next generation), defined in RFC 2080,[8] is an extension of RIPv2 for support of IPv6, the next generation Internet Protocol. The main differences between RIPv2 and RIPng are:

* Support of IPv6 networking.
* While RIPv2 supports RIPv1 updates authentication, RIPng does not. IPv6 routers were, at the time, supposed to use IPsec for authentication.
* RIPv2 allows attaching arbitrary tags to routes, RIPng does not;
* RIPv2 encodes the next-hop into each route entries, RIPng requires specific encoding of the next hop for a set of route entries.xxx

...

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Becareful with your Routers on HTTP Access

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

Before going through the problem, the following word should be considered to be read first:

What is HTTP?

-> HTTP stands for Hypertext Transfer Protocol, is an application-level protocol for distributed, collaborative, hypermedia information systems.Its use for retrieving inter-linked resources led to the establishment of the World Wide Web. HTTP uses port 80 as its default port. As you can see on Web Browser with the link address, Example: http://NetworkSecurityNotes.blogspot.com, my Network Security blog's address that can be browsed or viewed by using HTTP protocol. More additionally, on your Web Browser address bar, you can also browse any website with link address, Example: http://NetworkSecurityNotes.blogspot.com:80, the address will sill be redirected to the address http://NetworkSecurityNotes.blogspot.com. That's the port 80 is HTTP's default port.

How About HTTP Access?

-> Well, I just give a short definition what HTTP Access is. HTTP Access is a process of an access by using HTTP protocol.

Why on the Routers need to becareful with HTTP Access?

As you know on routers with Cisco IOS software equipped with a Web browser user interface that allows you to issue commands into the router via the Web interface. The Web browser user interface can be customized and tailored to your business environment. The HTTP server is disabled by default; when it's enabled, it introduces some new security vulnerabilities into your network. The HTTP server function, when it's enabled, gives all client devices with logical connectivity to the router the ability to monitor or modify the configuration of the router. All that needs to reside on the client is a software package that interprets packets on port 80. This is obviously a major security issue. So, the most concern with HTTP Access is about the security vulnerabilities when the HTTP Server is enabled on Routers.

So, How to take control of these security vulnerabilities?

The router software allows you to change the default port (port 80) that the HTTP server is running on. You can also configure an access list of specific hosts that are allowed Web access to the router and apply the access list to the HTTP server. Authentication of each user provides better security if you elect to use the router's HTTP server functions. Authentication can take place by one of four different methods:
> AAA: commonly stands for “Authentication, Authorization and Accounting"
> Enable: Indicates that the configured enable password is used for authentication. This is the default authentication method.
> Local: Indicates that the locally configured security database is used for authentication.
> TACACS+: stands for Terminal Access Controller Access-Control System Plus, a protocol which provides access control for routers, network access servers and other networked computing devices via one or more centralized servers. This option indicates that the Terminal Access Controller Access system is used for authentication.

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Understanding about Route Filtering to securing network

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

As my previous post about Routing Protocol Authentication, today post, I would like to find out about Route Filtering to securing network. 

What is Route Filtering?

Route Filtering is the process by Router, in which the certain routes are not considered for inclusion in the local route database, or not advertised to one's neighbours. During configuring Router, the Network Administrator need to be aware of which type of network route should be allowed to enter the Network Local or to go out to the remote Network. 

There are two Types of Filtering:

1.Input filtering

Input filtering is a filter is applied to routes as they are learned from a neighbour. A route that has been filtered out is discarded straight away, and hence not considered for inclusion into the local routing database.

2.Output filtering

Output filtering, a filter is applied to routes before they are announced to a neighbour. A route that has been filtered out is never learned by a neighbour, and hence not considered for inclusion in the remote route database.

Why Route Filtering? 

1.Route filtering enables the network administrator to keep tight control over route advertisements.

2.Route filters ensure that routers will advertise as well as accept legitimate networks. They work by regulating the flow of routes that are entered into or advertised out of the routing table.

3.Filtering the networks that are advertised out of a routing process or accepted into the routing process helps to increase security because, if no route is advertised to a downstream or upstream neighbor, then no route apparently exists to the network. 

4.Using Route Filtering to prevent routers on a local network from learning about routes that are dynamically advertised out on the interface, you can define the interface as passive. Defining an interface as passive keeps routing update messages from being sent through a router interface, preventing other systems on the interface from learning about routes dynamically from this router. You can configure a passive interface for all IP routing protocols except Border Gateway Protocol (BGP).

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Routing Protocol Authentication

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

What is Routing Protocol? 

A routing protocol is a protocol that specifies how routers communicate with each other, disseminating information that enables them to select routes between any two nodes on a computer network, the choice of the route being done by routing algorithms. Each router has a prior knowledge only of networks attached to it directly. A routing protocol shares this information first among immediate neighbors, and then throughout the network. This way, routers gain knowledge of the topology of the network.

The term routing protocol may refer specifically to one operating at layer three of the OSI model, which similarly disseminates topology information between routers.

Many routing protocols used in the public Internet are defined in documents called RFCs.

There are two major types of routing protocols, some with variants: link-state routing protocols and (path vector protocols) distance-vector routing protocols.

The specific characteristics of routing protocols include:

-the manner in which they either prevent routing loops from forming or break them up if they do

-the manner in which they select preferred routes, using information about hop costs

-the time they take to converge

-how well they scale up

-many other factors

Routing protocol authentication?

Routing protocol authentication prevents the introduction of false or unauthorized routing messages from unapproved sources. With authentication configured, the router will authenticate the source of each routing protocol packet that it receives from its neighbors. Routers exchange an authentication key or a password that is configured on each router. The key or password must match between neighbors.

There are two types of routing protocol authentication: plain text authentication and Message Digest 5 (MD5) authentication. 

1.Plain text authentication is generally not recommended because the authentication key is sent across the network in clear text, making plain text authentication susceptible to eavesdropping attempts. 

2.MD5 authentication creates a hash value from the key; the hash value instead of the actual password is exchanged between neighbors, preventing the password from being read because the hash, not the password, is transmitted across the network.

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Configuring Password Encryption

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

All Cisco console and Telnet passwords configured on the router are stored in plain text within the configuration of the router by default, thus making them easily readable. If someone issues the show running−config privileged mode command, the password is displayed. Another instance when the password can easily be read is if you store your configurations on a TFTP server, the intruder only needs to gain access into the TFTP machine, after which the intruder can read the
configuration with a simple text editor. Password encryption stores passwords in an encrypted manner on the router. The encryption is applied to all configured passwords on the router.

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Disabling Password Recovery

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

Setting passwords is the first line of defense against intruders. Sometimes passwords are forgotten and must be recovered. All Cisco password recovery procedures dictate that the user performs the password recovery process from the console port of the router or switch. There are, however, certain circumstances in which the widely available password recovery procedure should be disabled. One such circumstance is an emergency Add, Move, or Change (AMC), whereby a
networking device needs to be in a location that does not have the proper mechanisms in place for physical security, thus allowing an intruder a greater chance of circumventing traditional security measures.

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Setting Privilege Levels

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

Privilege levels associate router commands with each security level configured on the router. This allows for a finer granularity of control when restricting user access. There are 16 privilege levels contained within the router operating system. Level 2 to level 14 are customizable and allow you to configure multiple privilege levels and multiple passwords to enable certain users to have access to specific commands.

But most users of Cisco routers are familiar with only two privilege levels:

• User EXEC mode — privilege level 1


• Privileged EXEC mode — privilege level 15

When you log in to a Cisco router under the default configuration, you’re in user EXEC mode (level 1). From this mode, you have access to some information about the router, such as the status of interfaces, and you can view routes in the routing table. However, you can’t make any changes or view the running configuration file.

Because of these limitations, most Cisco router users immediately type enable to get out of user EXEC mode. By default, typing enable takes you to level 15, privileged EXEC mode. In the Cisco IOS, this level is equivalent to having root privileges in UNIX or administrator privileges in Windows. In other words, you have full access to the router.

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner

Securing Console Access

This blog is created for network security review, study and understanding about network related issues only! The blog is mainly focus on Network Security Notes about Network, Network Security, Network Technology, Network Labs review related Cisco and Microsoft technology ,Network Threats, Types of Network Threats, Network Alerts, Enterprise Security Policy and Audits, Security Policy and Audits,Logical Security, Physical and Logical Security, Physical Security,Cisco Products Review, Microsoft Products review, Cisco Routers, Routers Security, Console Access, Telnet Access, Network Attack, Network Attack report, Network management, Anti-virus, Network Security with Anti-virus, and All About Network Security... Thanks for your visit!

It's important to put the proper physical security mechanisms into place. If the proper physical

security mechanisms are not in place, an intruder could potentially bypass all other logical security mechanisms and gain access to the device. If an intruder can gain access to the administrative interface of the router, he could view and change the device's configuration and gain access to other networking equipment. The first thing you should do to prevent intruders from accomplishing is to set a console password. If the intruder has already gained physical access to the device, he'll attempt to gain network access through the console port first. The console port supports many different methods for authenticating a user and allowing access, some of which are listed here:
· Console password
· Local user database
· TACACS+ (Terminal Access Controller Access-Control System Plus) : is a protocol which provides access control for routers, network access servers and other networked computing devices via one or more centralized servers. TACACS+ provides separate authentication, authorization and accounting services.
· RADIUS(Remote Authentication Dial In User Service) : is a networking protocol that provides centralized access, authorization and accounting management for people or computers to connect and use a network service. When a person or device connects to a network often "Authentication" is required. Networks or services not requiring authentication are said to be anonymous or open.

Other sites you may want to see:

Entertainment on Flixya: http://visalittleboy.flixya.com/
WWE: http://visa-wwe.blogspot.com/
The Kingdom of Wonder: http://welcome2cambodia.blogspot.com/
Daily Blogging: http://visablogging.blogspot.com/
Love Sharing: http://visa-love.blogspot.com/
NetworkSecurity: http://networksecuritynotes.blogspot.com/
About Insurance:http://visa-insurance.blogspot.com
All about Love: http://visa-love.blogspot.com/
Learning English Online: http://visa-elb.blogspot.com/
Discovery Internet: http://visa-isp.blogspot.com/

Read more...

If you like this post, please subscribe below,thanks!

Enter your email address:

Delivered by FeedBurner